■ product introduction

The product is packaged in two components. The paint components are prepared by grinding epoxy resin, zinc powder, other antirust pigments and rheological additives and adding solvent. The other component is amine curing agent.

■ package specification

20kg / barrel, curing agent 3.5kg/barrel.

■ technical guidance

After mixing in the container, there is no hard block and it is in a uniform state

Constructability: barrier free for brushing

The appearance of the coating film is normal

Drying time,

Surface dry (23 ± 2 ℃) ≤ 1H

Dry (23 ± 2 ℃) ≤ 24h

Impact strength, kg.cm ≥ 50

Nonvolatile content,% ≥ 70

Metal zinc content in non-volatile matter,% ≥ 70

The nature of epoxy resin contains epoxy resin

■ main purpose

It is widely used in metallurgy, container, ship, vehicle manufacturing, steel plate pretreatment and shot blasting assembly line. At the same time, it is also suitable for anti rust of steel structures in other industries. It is an ideal paint for metal pretreatment and anti rust maintenance primer.

■ matching paint

Iron red epoxy antirust paint cloud iron red epoxy antirust paint

Yunnan iron red epoxy intermediate paint and various colors of chlorinated rubber anticorrosive finish

Various colors of acrylic high decorative finish and various colors of acrylic polyurethane enamel

Various colors of acrylic polyurethane topcoat and various colors of epoxy anticorrosive topcoat

■ surface treatment

The steel shall be sandblasted to Sa2.5, the surface roughness shall be 40 ~ 70UM, and the surface shall be free of grease and dirt.

■ painting reference

Paint density: 2.00-2.30g/cm3

Theoretical dosage: 150-170g / m2 (film thickness 40-50um, excluding loss) 70-90g / m2 (film thickness 23-30um, excluding loss)

Ratio: Paint: H - 100 curing agent = 10:1 (WT)

Applicable period: (23 ± 2 ℃) 6H

Diluent heavy duty anticorrosive epoxy diluent

Coating parameters

Airless spraying

The nozzle diameter is about 0.4-0.5mm

Discharge pressure 15MPa (about 150kg / cm3)

Air spraying

The nozzle diameter is about 2.0-2.5mm

Air pressure 0.3 - 0.6MPa (about 3 - 6kg / cm3)

■ storage and transportation

The product shall be stored in a cool, dry and ventilated place to prevent direct sunlight, isolate the fire source and keep away from the heat source. The storage period of paint is 12 months and that of curing agent is 12 months. During transportation, the products shall be protected from rain, sunlight and collision, and shall comply with the transportation regulations of the transportation department on dangerous chemicals.

■ precautions

1. Zinc salt (also known as white rust) can be formed on the surface of zinc rich primer, which shall not be exposed for a long time before painting. If a long coating interval is required, it is recommended to apply micaceous iron epoxy paint as a sealing layer as soon as possible to reduce the workload of secondary rust prevention. If it is placed in a clean indoor environment for several months and in a clean outdoor environment for 14 days, zinc salt will not form on the surface of the paint film. However, in the industrial and marine environment, zinc salt will be produced soon, and the time interval of painting shall be shortened as much as possible. On the surface with zinc salt, the secondary derusting treatment shall be carried out by cleaning sand blasting or mechanical derusting method, and all sundries shall be removed. Dry spraying is easy to occur during construction in high temperature season. In order to prevent dry spraying, dilute with diluent until dry spraying is not allowed.

2. Pay attention to ventilation at the construction site, take fire prevention, anti-static and other measures, and abide by the coating operation procedures and relevant regulations.

3. The substrate temperature is above 3 ℃ above the dew point, and the construction temperature is not lower than 5 ℃.

4. Quick drying curing agent shall be used when the construction temperature is lower than 5 ℃.